Adjusting the parking brake pedal - Arctic Cat Prowler Forums: Prowler UTV Forum
Arctic Cat Prowler General Discussions General discussions pertaining to the Arctic Cat Prowler.

 
LinkBack Thread Tools Display Modes
post #1 of 2 (permalink) Old 01-15-2011, 10:29 AM Thread Starter
Jounior Member
 
JPBILLIN's Avatar
 
Join Date: Jul 2010
Location: Phoenix
Posts: 193
 
Adjusting the parking brake pedal

i have the old crappy foot pedal parking brake on my 07 prowler. well i just bought a new cable and installed it i have not adjusted it or tightened it down to any setting. in the manual it gives a poor decription on how to adjust it properly, i searched the site and found little adjustment help maybe you guys could point me to a thread or explain the best way to make it functional. and when the cable will eventually stretch will i have to readjust the arm on the rear caliper or will just the housing nuts work by the foot pedal. i apprciate any input thanks
JPBILLIN is offline  
Sponsored Links
Advertisement
 
post #2 of 2 (permalink) Old 01-15-2011, 11:38 AM
Jounior Member
 
nater's Avatar
 
Join Date: May 2010
Location: utah
Posts: 56
 
I took this out of the manual I downloaded from

www.mymowerparts.com
It only took a few minutes to do and holds good now. There are pictures in the manual.

Parking Brake
CHECKING
Although the parking brake has been adjusted at the factory,
the brake should be checked for proper operation.
The brake must be maintained to be fully functional.
1. With the engine off, transmission in neutral, and
the parking brake set, attempt to move the vehicle.
2. If the rear wheels are locked, it is adjusted properly.
3. If the rear wheels are not locked, it must be
adjusted (set up).
ADJUSTING
To adjust (set up) the parking brake, use the following
procedure.


��
NOTE: Remove the four rear body screws securing

the belly panel to the frame and allow it to drop
down for better access to the parking brake actuator.
PR096
1. Remove the parking brake cable from the actuator
lever; then remove the actuator nut and actuator
lever. Note the position of the lever before removing.
PR098
2. Rotate the actuator clockwise (hand tight) until it
contacts the back of the piston; then rotate counterclockwise
approximately one spline.
Install the actuator lever in the position noted in
step 1; then install the actuator nut and tighten to
35 ft-lb.
PR098A
4. Install the parking brake cable and adjust nuts so
the parking brake holds the vehicle when set and
fully releases it when released.
PR097A
TOC Back to Section TOC


Last edited by nater; 01-16-2011 at 07:07 PM.
nater is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Arctic Cat Prowler Forums: Prowler UTV Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome
 


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61