Flywheel removal on a 650 H1 - Arctic Cat Prowler Forums: Prowler UTV Forum
Arctic Cat Prowler General Discussions General discussions pertaining to the Arctic Cat Prowler.

Reply
 
LinkBack Thread Tools Display Modes
post #1 of 38 (permalink) Old 05-16-2011, 01:36 PM Thread Starter
Jounior Member
 
Join Date: Mar 2011
Location: Newfoundland
Posts: 130
 
Flywheel removal on a 650 H1

Hey all, I've just split the casing on the way to removing a damaged crankshaft. Not sure of the method for removing the flywheel. The AC manual says to use the "Magneto Rotor Remover set (p/n0444-075)".

Like ever other backyard mechanic, I don't have one of those. Is there an easy way to remove the flywheel? I've got the 22mm nut removed....and now.....????

Thanks in advance
paradisedude is offline  
Sponsored Links
Advertisement
 
post #2 of 38 (permalink) Old 05-16-2011, 04:04 PM
Jounior Member
 
dla67's Avatar
 
Join Date: Jun 2010
Location: Ohio
Posts: 244
 
No you must get the puller......sorry.
dla67 is offline  
post #3 of 38 (permalink) Old 05-16-2011, 04:55 PM Thread Starter
Jounior Member
 
Join Date: Mar 2011
Location: Newfoundland
Posts: 130
 
Just spent a few more minutes disassembling. I should be able to bolt a puller onto 2 of the threaded torx bolt holes of the starter clutch. Should be able to jack it off from the crankshaft like that.

Can anyone confirm? Don't want to do any damage.
paradisedude is offline  
 
post #4 of 38 (permalink) Old 05-16-2011, 07:04 PM
Jounior Member
 
dla67's Avatar
 
Join Date: Jun 2010
Location: Ohio
Posts: 244
 
I tried a 3 bar puller in the torx bolt holes with no luck. Used the arctic cat puller and it came off easily. DONT use heat the chrome on the inside of the flywheel is very thin and will pop off. I hope this helps Good Luck
dla67 is offline  
post #5 of 38 (permalink) Old 05-16-2011, 07:17 PM Thread Starter
Jounior Member
 
Join Date: Mar 2011
Location: Newfoundland
Posts: 130
 
Hmmm..that's not the news I was hoping for...thanks for the advice though. I'll probably do the same, try a 3 bar and cross my fingers. The crankshaft is toast anyway, so even if I have to bore it out and deal with it in a lathe or press, that's not all bad.
paradisedude is offline  
post #6 of 38 (permalink) Old 05-16-2011, 09:49 PM
Rides all the time
 
riddler28's Avatar
 
Join Date: Mar 2010
Location: alaska
Posts: 1,324
 
The AC puller is what I had to use. It came off easily.
You may bring in the motor to the dealer and they could zip it off for you.
My dealer let me borrow one for the day.
riddler28 is offline  
post #7 of 38 (permalink) Old 05-17-2011, 05:21 AM Thread Starter
Jounior Member
 
Join Date: Mar 2011
Location: Newfoundland
Posts: 130
 
I've got my doubts that they will loan it out, I'll try an off the shelf 3 bar puller and if that doesn't do it perhaps I'll make a 6 hole puller and jack it off with that.
paradisedude is offline  
post #8 of 38 (permalink) Old 05-18-2011, 01:26 PM Thread Starter
Jounior Member
 
Join Date: Mar 2011
Location: Newfoundland
Posts: 130
 
So i decided to skip the 3 bar puller and made up a puller using all 6 of the starter bolt threaded holes. I was picturing the 3 bolts snapping or stripping out the threaded starter holes.

Worked out great. Probably could have gotten away with a 2 hole puller, better safe than sorry though.
Attached Thumbnails
Click image for larger version

Name:	DSCN4730.JPG
Views:	2256
Size:	88.2 KB
ID:	2261  
paradisedude is offline  
post #9 of 38 (permalink) Old 05-18-2011, 02:46 PM
Jounior Member
 
dla67's Avatar
 
Join Date: Jun 2010
Location: Ohio
Posts: 244
 
I'm glad it worked for you and good luck on your rebuild!
dla67 is offline  
post #10 of 38 (permalink) Old 05-18-2011, 02:48 PM
Jounior Member
 
dla67's Avatar
 
Join Date: Jun 2010
Location: Ohio
Posts: 244
 
Watch your alignment dowl's they will fall out when you start rolling your block around.
dla67 is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Arctic Cat Prowler Forums: Prowler UTV Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome
 


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73